How to Make Realistic Crepe Paper Daffodils — Easy Step-by-Step DIY

Paper Crafts

Creating crepe paper daffodils is a delightful craft that will bring a touch of spring into your home all year round. This easy step-by-step tutorial walks you through cutting, shaping and assembling a realistic daffodil using simple supplies: crepe paper, floral wire and tape, plus basic tools. Follow the photos and directions below to make single stems or a whole bouquet.

Creating crepe paper daffodils is a delightful craft that will bring a touch of spring into your home all year round! These charming flowers make for a fun and easy DIY project that anyone can enjoy. With just a few simple materials and a bit of creativity, you can brighten up your space with these lovely blooms. Whether you're a seasoned crafter or just starting out, crafting crepe paper daffodils is a wonderful way to add a pop of color and cheer to any room. So gather your supplies, put on some music, and let's get crafting!

Materials:

Crepe paper

Floral tape

Floral wire

Equipment:

Scissors

Glue gun

Needle nose pliers

Instructions:

Step 1: Find what you need

Gather your supplies and materials.

Supplies laid out: crepe paper, floral wire, floral tape, scissors, glue gun and pliers.

Step 2: Create the center of the flower

Cut a piece of yellow crepe paper to be 1 by 1-1/2 inches.

The grain of the crepe paper should be parallel to the long edge (the lines in the paper should be vertical for the 1-1/2 inch section).

Cut a 1 × 1½ in piece of yellow crepe paper with the grain parallel to the long edge.

Cut along the short edge (the cuts should go with the grain), making a fringe that goes just over 1/2 way down the paper.

Make fringe cuts along the short edge, cutting about halfway down.

Cut another piece of yellow crepe paper to be 1-1/2 by 3-1/2 inches, with the grain of the paper parallel to the short edge.

Cut a second yellow rectangle (1½ × 3½ in.), grain parallel to the short edge.

Cut small “V” shapes along one of the long edges. It’s okay (good, actually!) if they’re not perfectly even.

Cut small V shapes along the long edge to shape the trumpet.

Add a line of hot glue along one short end of this paper.

Apply a line of hot glue along one short end.

Glue it to the other end, creating a cylinder.

Glue the strip into a cylinder to form the trumpet base.

Scrunch the flat bottom together, using your finger to keep the top part open.

Scrunch the bottom to close the cylinder while keeping the top open.

Step 3: Create the petals

Cut a piece of white crepe paper to be 1-3/4 by 2-1/2 inches. The grain of the crepe paper should be parallel to the long edge.

Cut white crepe paper rectangles for petals (1¾ × 2½ in.).

Cut a petal shape from the white paper.

Pinch the flat bottom of the petal and twist it to keep it together.

Pinch and twist the petal base to give it dimension.

Repeat, making 5 more petals. (You should have 6 petals altogether.)

Step 4: Make the leaves and stem

Cut a green piece of crepe paper to be about 1-1/2 by 10 inches. The grain of the crepe paper should be parallel to the long edge.

Cut a green strip (about 1½ × 10 in.) for leaves.

Cut from the center of the paper up to the top right corner. Repeat, cutting up to the top left corner, creating 3 pointed leaves.

Cut three pointed leaves from the strip by cutting from center to the corners.

Take a piece of floral wire and cut it to be 10 inches long. Use needle nose pliers to curve one end into a loop.

Create a 10 in floral wire and curve one end into a loop.

Wrap green floral tape around the wire, including the curved part, to create the stem.

Wrap green floral tape around the wire to form the stem.

Step 5: Assemble the flower

Add hot glue to both sides of the wire at the looped end.

Add hot glue to both sides of the wire loop to attach the center.

Wrap the fringed yellow paper around the stem with the fringe side up (away from the wire).

Wrap the fringed yellow piece around the stem with the fringe facing up.

Twist the fringe together, then add hot glue around the bottom of it.

Twist the fringe together and secure with hot glue.

Open the cylinder piece back up and slide it down around the fringe. Scrunch it back into shape, then fold the pointed edge down slightly so it sticks out.

Slide the cylinder over the fringed center to form the trumpet; fold the edge out slightly.

Add hot glue to the bottom twist of a petal and attach it to the yellow part of the flower.

Glue petals to the yellow center, starting with one and spacing evenly.

Add the next 2 petals onto the flower. They should fit evenly around.

Add the next two petals so three are evenly spaced around the center.

Glue the remaining 3 petals, placing them between the first 3 petals.

Glue the remaining three petals between the first set to complete the bloom.

Shape the petals, pulling on each side to stretch them into shape.

Shape each petal by gently stretching and curving the crepe paper.

Add hot glue along the bottom of a leaf.

Add hot glue to the base of each leaf before attaching to the stem.

Wrap the first leaf around the stem about 2/3 of the way down. Repeat with the other 2 leaves, placing the second further down. Finish with the third leaf around the bottom of the stem.

Wrap the leaves around the stem at staggered positions for a finished look.

Your crepe paper daffodil is complete!

accessories, easy diy, project

Like!

☆ Add To Favorites

107

No comments